Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Before
After
Before
After
Before
AfterFast, Reliable Gate Repair Across Keller
Gate repair in Keller, TX typically runs $185-$680 depending on what failed, and most jobs we fix in a single visit. If your automatic gate won’t open, sags on its hinges, or scrapes the ground after a rain, we can usually have a technician at your driveway the same day. Call (817) 674-6552 and a live person answers, 24/7.
Keller isn’t a generic suburb, and gate work here isn’t generic either. The city’s neighborhoods were built out fast between 1993 and 2008, which means thousands of ornamental iron gates and automatic operators are now 15 to 30 years old and wearing out at the same time. Add Blackland Prairie clay that moves gate posts every dry summer and wet winter, plus HOA design rules that won’t tolerate a mismatched replacement, and you need a gate company that knows Keller block by block. Our Gate Repair team works on Keller driveways weekly, from Hidden Lakes to the horse properties along Keller Hicks Road.
Why Vance Gate Repair Coppell Is Keller’s Preferred Gate Repair Company
Our founder Adrian Vance started in commercial access control back in 2014, which is why every residential job we touch gets the same documentation a commercial site would require. That means a written price before any work starts, a photo record of what we found and what we changed, and a 365-Day Done Right Promise on every repair. Keller homeowners who’ve had other companies leave a verbal estimate and a shrug find that refreshing. We’ve completed 22,000+ gates repaired and installed since 2014, every one with a written price handed over before a tool came out.
Dispatch for Keller jobs runs out of our DFW office, and we schedule crews to Keller daily. Because we work the same streets repeatedly, we already know which HOA architectural boards in Keller require pre-approval paperwork before a finish color or operator changes, and we factor that into the job so you don’t get a violation letter two weeks later. That’s local knowledge you won’t get from a generic gate company that drives in from across the metroplex. Under Haven Standard Clause 1 (“Have it in writing”), your price is set and signed before we begin. Under Clause 4 (“Evidence on every job”), you get a documented photo record of every adjustment and part number installed before we leave.
Our Gate Repair Services in Keller
We don’t outsource anything. The technician who calls you from the driveway is the same background-checked, uniformed professional who does the work, and you’ll know their name and see their photo before arrival. Here’s what we handle most often in Keller:
Electric Gate Repair
Keller’s boom-era automatic gates run on electric operators that are now aging out in waves. When a control board burns out after a freeze or a photo-eye (the infrared beam that stops the gate if something crosses the path) drifts out of alignment, the gate either won’t move or won’t stop moving when it should. We diagnose the board, the wiring, the limit switches, and the safety edges in one visit, and we carry replacement boards for LiftMaster, FAAC, Viking, DoorKing, Ghost Controls, Elite, and more on the truck.
Automatic Gate Repair
Keller’s clay soil puts stress on automatic swing gate operators in a way that’s predictable to us and confusing to homeowners. When the post shifts a few degrees, the operator’s pinion gear doesn’t mesh with the rack cleanly anymore. It grinds. Then it strips. If your gate groans, jerks, or reverses mid-travel, the fix is usually mechanical alignment, not a whole new motor. We check and adjust travel limits, force settings, and gear mesh, then photograph the final readings so the next adjustment isn’t a guess.
Hinge & Post Repair
Ornamental iron gates in Keller are heavy, often 300-600 pounds on newer estate homes. When the Blackland clay under a post shrinks during a dry North Texas summer, the post leans, the gate drops, and the latch no longer lines up. We excavate around the post, pour a new footing with proper soil compaction, re-hang the gate, and adjust the operator to the new geometry. For HOA-governed properties, we match the existing powder-coat finish and picket profile so the repair is invisible.
Gate Realignment
A gate that drags, won’t latch, or sits crooked usually isn’t broken; it has moved. Keller sees this every year as wet winters swell the clay and dry summers shrink it. We realign hinge points, re-square the gate frame, and reset the latch strike so the gate closes with one finger and stays closed. This service often prevents a full hinge or post replacement if we catch it early.
We also handle Gate Repair in Keller for welded ornamental gates, rust-through sections, cracked welds on steel frames, and lock replacement on both automated and manual gates.
What happens when you call
- 1
A real person answersNo phone trees - you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Before
AfterTrusted Brands We Service in Keller
We service nine major gate-automation brands, so there’s no reason to swap a whole system just because one component failed. On Keller trucks we stock common parts for Viking, DoorKing, Elite, and Ghost Controls, plus LiftMaster, FAAC, BFT, Linear, and Mighty Mule. If your existing operator matches your HOA’s approved hardware list, we fix it in place. If the manufactured housing is cracked beyond repair, we quote a drop-in replacement that works with your existing wiring, safety edges, and remote controls. Either way, the written price is in your hand before we turn a screw.
Common Gate Repair Problems We See in Keller Homes
- Post heave and gate binding from Blackland Prairie clay. Keller sits on expansive soil that shrinks in drought and swells after rain. The seasonal cycle slowly pulls posts out of plumb, which makes gates bind, sag, and scrape asphalt. We fix the footing, not just the symptom, with deeper embedment and proper compaction.
- Board and actuator failures after hard freezes. The February 2021 freeze killed a lot of gate control boards in Keller that weren’t rated for sub-20°F exposure. Hydraulic actuators cracked too. Every few winters the mid-cities gets a repeat, and we run board-replacement calls for weeks afterward. If your gate died in a freeze, plan on a board swap, not a motor rebuild.
- HOA finish-matching constraints on replacement parts. Many Keller subdivisions require architectural review before you change a gate’s finish color, operator model, or picket style. A generic off-the-shelf bronze part that doesn’t match the existing powder coat can put you in violation. We source exact-match finishes and file the paperwork where the HOA requires pre-approval.
- Ranch pipe gate wear on horse-property parcels. Not every Keller gate is ornamental. The acreage tracts have heavy pipe gates with slide latches and wheel supports that wear out from daily use with stock trailers and horses. We weld cracked frames, replace hinge barrels, and rebuild latch posts on the same blocks where we service automated estate gates.
Pricing for Gate Repair in Keller, TX
Here’s what Keller homeowners should expect. A basic gate realignment or latch adjustment runs $185-$240. Hinge replacement on a standard single ornamental gate runs $320-$480 including new hardware and alignment. A post that needs excavation, a new footing, and re-hanging runs $550-$850 depending on soil access and whether we’re matching HOA finishes. Control board replacement runs $290-$520 for common LiftMaster, Viking, DoorKing, or Ghost Controls boards; a full swing-gate operator replacement runs $850-$1,700 depending on brand, weight rating, and whether the arm bracket and mounting plate are intact. Pipe gate welding and frame repair on ranch gates runs $200-$400 before materials. Every quote is written, line-item priced, and agreed to before any work starts. Call (817) 674-6552 for a free estimate, and we’ll hand you a price in writing on site, not a range over the phone with a shrug.
We Also Serve Cities Near Keller
Our Keller crews work all around the mid-cities. We serve North Richland Hills to the south, Southlake to the east, Colleyville to the southeast, and Hurst to the south. If you’re just outside Keller on the north side or out toward the Keller-Haslet line, call (817) 674-6552 and we’ll confirm your street is in our daily route.
Serving Keller, TX - Our Local Coverage Area
We’re based in the Keller area and know this community well. Use the map below to see our service coverage - if you’re nearby, we can almost certainly help.
FAQs - Gate Repair in Keller
Keller’s primary residential buildout happened between roughly 1993 and 2008, when the city grew outward from the town center into large-lot subdivisions. The ornamental iron driveway gates and electric operators installed during that boom are now 15 to 30 years old, and electric gate components don’t fail evenly; they cluster at the 15-20 year mark, which means a wave of simultaneous control board, actuator, and hinge failures across the city. If your neighbors’ gates have been dying lately, yours isn’t far behind. Call (817) 674-6552 and we’ll inspect yours before it strands you outside.
Keller sits on Blackland Prairie clay that shrinks during the hot, dry North Texas summers and swells when the fall and winter rains return. That seasonal expansion and contraction moves gate posts out of plumb by fractions of an inch each year until the gate binds, the latch misses the strike, or the operator’s gears strip. A proper repair means re-excavating the post, setting it deeper with compacted fill, and sometimes installing a concrete collar below grade to stabilize it. We do exactly that, then photograph the plumb reading and the new footing before we close the hole.
In many Keller subdivisions, yes. HOA architectural review boards commonly require written approval before gate hardware, finish colors, or picket profiles can change. If you replace a black powder-coated latch with a standard bronze one that doesn’t match the existing gate, or swap an operator model that’s on the HOA’s approved list for one that isn’t, you can end up with a violation letter and a demand to redo the work. We know which Keller neighborhoods require pre-approval and we file the paperwork before the job closes. Bring your HOA’s written requirements to the first appointment and we’ll work within them.
Yes. The permanent fix is deeper embedment and a properly compacted footing, often with a concrete collar that resists the clay’s seasonal movement. We excavate the old footing, re-set the post with the hinge centerline verified in both directions, and let the concrete cure before re-hanging the gate and adjusting the operator. We also photograph the post depth and plumb reading before backfill so you have a documented record of what was done, which helps if you sell the house and the buyer’s inspector asks.
Yes. Keller still has horse-property zoning along its northern and western edge, with heavy pipe and panel gates that get used daily with horses, trailers, and feed trucks. We weld cracked frames, replace hinge barrels, rebuild latch posts, and install wheel supports on the same days we work on automated ornamental gates in Hidden Lakes or Marshall Ridge. The tools and skills are different from a swing-gate operator repair, but our technicians carry both sets, so one call handles either style of gate. Call (817) 674-6552 and tell us what you’re running; we’ll dispatch the right tech and the right truck.
Written by Adrian Vance, Owner at Vance Gate Repair Coppell, serving Keller since founding the company in 2014.
If your Keller gate is sagging, stuck, or silent, call (817) 674-6552. A live person answers 24/7, the estimate is free, and the price is in writing before any work begins.